Skip to content

Speaker and stereo channel test

Verify stereo wiring, left/right channel separation, phase polarity, and low-end response.

Left speaker

Sends a soft 440 Hz tone strictly to the left channel (L = 100%, R = 0%).

How to use Speaker test

  1. Adjust output headroom before playback. Drag Test volume between 10% and 90% (defaulting to 45%) so sudden sine tones or low-end sweeps stay comfortable.
  2. Verify physical left and right wiring. Click Left speaker, Center (both in phase), and Right speaker to test channel assignment and confirm a centered phantom image.
  3. Check driver polarity and low-end response. Run Phase polarity check on pink noise or launch Bass sweep (20-160 Hz) and Full sweep (20-16,000 Hz), clicking Stop audio anytime to silence playback.
  4. Export an offline reference clip. Click Download test WAV to save a 16-bit 48 kHz stereo PCM file for smart TVs, soundbars, or car receivers.

Your camera, microphone and recordings stay on this device. Nothing is uploaded or streamed anywhere.

How does discrete stereo routing isolate left and right speakers?

This browser speaker test builds a two-channel synthesis graph inside an AudioContext so left and right speakers or headphones receive exact signals without streaming compression. Every preset runs locally in tab memory, letting you check wiring and balance with zero extra software.

Under the W3C Web Audio API 1.1 specification, createChannelMerger(2) maps two independent GainNode outputs directly onto channels 0 and 1. Discrete gain routing sets the silent channel strictly to zero (L = 100%, R = 0% or L = 0%, R = 100%) while supporting signed negative multipliers for polarity inversion.

Distinct pitches for left and right ear checks

Clicking Left speaker plays a 440 Hz sine (A4) for 2.5 seconds on the left channel, while Right speaker plays 523.25 Hz (C5) for 2.5 seconds on the right. Two distinct pitches make swapped cables or flipped earbuds obvious right away.

Selecting Center (both in phase) drives both drivers equally at 0.85 amplitude on 440 Hz for 2.5 seconds. On properly wired stereo monitors, that shared signal locks directly between both speakers.

Ramping gain envelopes to stop clicks and pops

Cutting an oscillator mid-cycle creates audible pops that mask subtle distortion. Playback ramps up over 20 ms to your Test volume level (10% to 90%, 45% default) and fades out across 30 ms before disconnecting nodes 80 ms after completion.

Clicking Stop audio halts active nodes right away if output feels too loud. For continuous custom pitches beyond these clips, play exact Hz sine waves and noise bursts up to 20,000 Hz.

In-phase vs out-of-phase audio and stereo polarity checks

Reversing positive (+) and negative (-) wires on one passive speaker pushes one cone out while the other pulls in. That 180-degree cancellation hollows out center vocals and weakens bass.

When comparing panning against the MDN Web StereoPannerNode Reference, standard panners cannot invert a single channel cleanly to -1. Separate gain nodes let Phase polarity check apply +0.85 left and -0.85 (R = -L) right simultaneously.

Listening for hollow cancellation on pink noise

Pure sine tones can sound ambiguous out of phase indoors because standing waves shift apparent level as you move. Phase polarity check instead plays 3 seconds of pink noise from a deterministic PRNG (0x9e3779b9) through a seven-stage Paul Kellet -3 dB-per-octave filter.

  • Healthy wiring: Center (both in phase) locks tightly between monitors, whereas Phase polarity check sounds wide and noticeably hollow in the middle.
  • Reversed polarity: If Phase polarity check focuses the image while Center (both in phase) feels hollow, swap the red and black wires on one speaker only.

Comparing all six diagnostic test presets

Each button in the Speaker test grid targets a specific wiring, polarity, or response check. Review exact preset parameters in the table before testing or exporting clips.

Preset button Signal type Channel routing Duration Primary diagnostic check
Left speaker 440 Hz sine (A4) L = 100%, R = 0% 2.5 seconds Confirms left channel identity and zero cross-talk
Center (both in phase) 440 Hz sine (A4) L = 0.85, R = 0.85 2.5 seconds Verifies centered phantom image and matched volume
Right speaker 523.25 Hz sine (C5) L = 0%, R = 100% 2.5 seconds Confirms right channel identity using a higher pitch
Phase polarity check Pink noise (-3 dB/oct) L = 0.85, R = -0.85 3 seconds Exposes swapped +/- speaker cables via cancellation
Bass sweep (20-160 Hz) Logarithmic sine sweep Both in phase 5 seconds Reveals subwoofer gaps, port chuffing, and buzzes
Full sweep (20-16,000 Hz) Logarithmic sine sweep Both in phase 8 seconds Tracks left/right image drift and tweeter roll-off

If your speakers pass channel separation checks during a headset setup, test the attached mic next with a raw un-suppressed microphone input check in another tab. Verifying playback and capture independently prevents browser echo-cancellation filters from hiding hardware faults.

Running a bass sweep from 20 to 160 Hz and saving WAV clips

Static single tones miss narrow resonant peaks where a desk panel rattles or a crossover drops mid-bass energy. Exponential frequency sweeping glides continuously across frequencies so defective enclosures and room modes stand out clearly.

Diagnosing subwoofer crossovers and cabinet rattles

Bass sweep (20-160 Hz) sweeps exponentially over 5 seconds (exponentialRampToValueAtTime), spending equal time on every musical octave rather than rushing past deep notes. Small laptop drivers typically vanish below 80 Hz, while healthy subwoofers should transition smoothly through the 80 Hz to 120 Hz crossover region without sudden dips or cabinet buzz.

Full sweep (20-16,000 Hz) runs for 8 seconds across nearly ten octaves. Focus on whether the phantom center wanders left or right as pitch climbs, which exposes mismatched tweeters or clogged earbud grilles, and verify mechanical keycaps when audio alerts misfire if muted system keys affect playback shortcuts.

Exporting 48 kHz 16-bit PCM files with Download test WAV

Web browsers cannot play directly through an offline receiver, smart television, or car USB head unit. Clicking Download test WAV synthesizes the last selected preset (speaker-test-<id>.wav) directly in memory as uncompressed stereo PCM audio without server round-trips.

Following the Library of Congress WAVE Audio Format container specification, each download writes a standard 44-byte RIFF/WAVE header (fmt chunk tag 1) followed by 48,000 Hz, 16 bits per sample stereo frames. A 15 ms raised-cosine envelope smoothly tapers both ends of the clip so looping playback on external hardware never pops.

Fixing mono Bluetooth profiles and muted browser output

Wireless headsets frequently fail left/right separation checks even though the hardware is completely intact. Bluetooth audio uses separate profiles for music playback versus voice calls: A2DP carries full stereo audio, whereas Hands-Free Profile (HFP) drops down to mono whenever any open app accesses the headset microphone.

Close browser tabs or conferencing tools holding your headset mic, then verify your operating system output points to the stereo headphones endpoint rather than the headset hands-free endpoint. Also confirm your OS accessibility settings do not enable mono audio summing or shift the balance slider away from center.

When an online speaker test produces no sound after a click, browsers may still hold the tab muted or await a fresh gesture to wake a suspended AudioContext. Check physical 3.5 mm TRS jack seating, verify external amp power, and adjust Test volume between 10% and 90% (45% default) alongside your OS mixer.

Tip: Mouse scroll notches can rattle loudly during low-volume acoustic room tests. Try isolate noisy scroll notches alongside speaker output checks if mechanical desktop noise competes with quiet sweeps.

Questions

What should an out-of-phase speaker polarity check sound like?

When both drivers are wired with matching polarity, Phase polarity check sounds wide, hollow, and pulled outside the monitors because inverted channels cancel center energy. If out-of-phase sounds tighter than Center, one speaker wire has reversed positive and negative leads.

Why do left and right Bluetooth channels play mono audio?

Bluetooth headsets switch from A2DP stereo playback to Hands-Free Profile (HFP) mono audio whenever a voice app or browser tab opens the microphone. Close video calls or change your system output back to the stereo headphone profile before testing.

Why does the right speaker play a higher pitch than the left?

Left speaker plays a 440 Hz concert A4 tone while Right speaker plays a 523.25 Hz C5 tone. Using two distinct musical pitches lets you verify swapped cables or flipped earbuds immediately even if one channel leaks faintly.

Which audio format does Download test WAV export?

Download test WAV generates an uncompressed 16-bit stereo RIFF/WAVE file sampled at 48,000 Hz for whichever preset you clicked last. Every file includes a 15 ms raised-cosine fade at both ends so televisions and car stereos never click.

How does the 20 to 160 Hz bass sweep diagnose cabinet rattles?

The 5-second Bass sweep glides logarithmically from 20 Hz to 160 Hz, spending equal time per musical octave. Steady buzzing at a specific pitch exposes loose desk screws, rattling speaker grilles, or a poorly tuned subwoofer crossover gap.

Why does browser audio fail to start on the first click?

Modern browsers suspend new AudioContext instances until a direct button press resumes playback, or an operating system mixer mutes the browser tab. Check your system output device and click any preset button once to unlock audio.

Updated